OVERVIEW
Lantech T(P)GS-R6804XT is a high performance OS4 Ethernet switch with 4 1G/2.5G + 8 1G/2.5G/5G/10G. PoE model has 8 (incl.4 copper + 4 uplink 10GT copper) PoE 802.3af/at ports which provides advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports enhanced mode with easy configuration. The comprehensive QoS, advanced security including INGRESS ACL L2/L3, TACACS+, SSH v2/SSL and Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port are supported and also required in large network. It also supports10K Jumbo frames.
Up to 8(at) PoE at/af ports w/advanced PoE management
Compliant with 802.3af/at standard, the Lantech TPGS-R6804XT is able to feed each PoE port up to 30 Watt at each PoE port for various IP PD devices. Lantech TPGS-R6804XT supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE ports can be Enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.
Miss-wiring avoidance, node failure protection, Loop protection
The T(P)GS-R6804XT also embedded several features for strong and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech T(P)GS-R6804XT being able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
Support PXE to verify switch with latest or certain firmware
The switch can check its firmware version during booting time via PXE protocol. If switch finds any newer version, it will upload automatically.
DHCP option 82 & Port based, Mac based DHCP, Option66, DHCP Snooping, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch), it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Snooping is supported. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Basic IPv6 DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user-friendly UI, innovative auto topology drawing and topology demo makes T(P)GS-R6804XT much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech T(P)GS-R6804XT features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers enhanced ring and basic ring by easy setup than others. It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI. MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
Built-in IEC 61375-3-4 ECN (Ethernet Consist Network) to work with IEC61375-2-5 TBN
Lantech OS4 Ethernet switches comply with IEC 61375-3-4 (ECN) standard. The support of Ethernet Consist Network allows interconnection between end devices located in single consist of train and interoperability with IEC61375-2-5 (TBN).
Enhanced Storm control
Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces and the detection is more precise and reaction is more efficient.
Optional L3Lite/L3/ETBN to be upgradable
Lantech OS4 are optional upgradable to L3 Lite/ L3 or ETBN communication protocols for future expansion. The optional L3Lite includes editable routing table, VRRP, Router-on-a-stick, Inter- VLAN routing. Optional ETBN complies with IEC61375-2-5 ETBN for Train Backbone Network.
QinQ, QoS and GVRP supported
It supports the QinQ, QoS and GVRP for large VLAN segmentation.
Protocol based VLAN; Subnet based VLAN
The protocol-based VLAN processes traffic based on protocol. It filters IP traffic from nearby end-stations using a particular protocol such as IP, IPX, ARP or other Ethernet-types in a Hex value. Subnet based VLANs group traffics into logical VLANs based on the source IP address and IP subnet. The above features can help to build VLAN in the network mixed with managed and un-managed switch as to define packets to which VLAN group based on protocol or subnet.
IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.
Editable configuration file; USB port for import/export configuration
The configuration file of Lantech T(P)GS-R6804XT can be imported and edited with word processor for the following switches to configure with ease. The USB port can import/export the configuration from/to USB dongle and also to upgrade firmware from USB dongle.
Event log & message; 2DI + 2DO; Factory default pin
T(P)GS-R6804XT provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the outside alarm and switch will send alert information to IP network with email and traps. The factory reset pin can restore the setting back to factory default.
Enhanced environmental monitoring for switch inside information
The enhanced environmental monitoring can detect switch overall temperature, total power load, actual input voltage and current. It can send the SNMP traps alert when abnormal.
Optional smart bypass protection on dual 10G copper ports
The bypass relay is set to bypass the switch to the next one when power is off to prevent network disruption. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. Optional smart bypass (Up to two pairs) can be activated when switch encounters power failure or CPU hang. (-BT/-BBT model)
Dual WVI input with Inrush current protection
The T(P)GS-R6804XT WVI model accepts 16.8~137.5VDC dual input with galvanic protection and PoE model can feed 54V output for PoE feeding with 80W budget. A voltage which can be minimal 0,5 Un nominal voltage (when Vin≧36V) and/or a voltage which can be maximal 1,5 Un nominal voltage for more than 1000 consecutive ms (one second). The inrush current on initial power up can be limited lower than 10 x nominal current and for less than 1ms.
EN50155, EN45545-2; EN61373 compliance; High ESD protection
T(P)GS-R6804XT passed serious tests under extensive Industrial EMI and Safety standards. With EN45545-2 Fire & Smoke and EN50155 verification, the T(P)GS-R6804XT is best switch for railway on-board/track side, vehicle, and mining applications. For more usage flexibilities, T(P)GS-R6804XT supports wide operating temperature from -40°C to 70°C. (85°C operations for 10min.)
SPECIFICATIONS
Hardware Specifications
Standards
|
IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T IEEE802.3ak 10Gbase-T IEEE802.3x Flow Control and Back Pressure IEEE802.3ad Port trunk with LACP IEEE802.1d Spanning Tree IEEE802.1w Rapid Spanning Tree IEEE802.1s Multiple Spanning Tree IEEE802.3ad Link Aggregation Control Protocol (LACP) IEEE802.1AB Link Layer Discovery Protocol (LLDP) IEEE802.1X User Authentication (Radius) IEEE802.1p Class of Service IEEE802.1Q VLAN Tag IEEE802.3at/af Power over Ethernet
|
Switch Architecture
|
Back-plane (Switching Fabric): 180Gbps
|
Mac Address
|
16K MAC address table
|
Jumbo frame
|
10KB
|
Connectors
|
10/100/1000T/2.5G Copper: 4 x M12 8-pole X-coded with Auto MDI/MDI-X function 1G/2.5G/5G/10G Copper: 8 x M12 8-pole X-coded Power Input connector: 1 x M12 4-pole Male A-coded Reset/Console/USB: 1 x M12 8-pole A-coded DIDO: 1 x M12 5-pole A-coded
|
Network Cable
|
1000Base-T: 4-pair STP Cat5E/6 cable; 10G Copper: 4-pair STP Cat6a/7 cable
|
LED
|
Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red); RM (Green) 100/1G/2.5G Ethernet port: Link/Activity (Green) 1G/2.5G/5G/10G port: speed (1G/2.5G/5G: Yellow; 10G: Orange) PoE : Link/Act (Green) (PoE model)
|
DI/DO
|
2 Digital Input (DI): Level 0: -30~2V / Level 1: 10~30V Max. input current:8mA 2 Digital Output (DO): Open collector to 80 VDC, 50mA
|
Operating Humidity
|
5% ~ 95% (Non-condensing)
|
Operating Temperature
|
-40°C~70°C / -40°F~158°F (85°C operation for 10min.)
|
Storage Temperature
|
-40°C~85°C / -40°F~185°F
|
Power Supply
|
Dual DC input, 16.8VDC~137.5VDC
|
PoE Budget (PoE model)
|
80W
|
PoE pin assignment (PoE model)
|
M12 port #1~#4; #7~#10; support IEEE 802.3at/af End-point, Alternative A mode
|
Power Consumption
|
max. 52.45W w/o PoE load
|
Dimensions
|
IP54: Aluminum case 304mm(W)x195mm(H)x89.5mm(D)
|
Weight
|
4.8 kgs
|
Installation
|
Wall Mount Design
|
EMI & EMS
|
FCC Part 15 Class A EN61000-6-2 EN61000-6-4 CE EN55032 Class A CE EN55024: CE EN61000-4-2 (ESD) Level 3 CE EN61000-4-3 (RS) Level 3 CE EN61000-4-4 (EFT) Level 3 CE EN61000-4-5 ED3 (Surge) Level 3 CE EN61000-4-6 (CS) Level 3 CE N61000-4-8 (Magnetic field) Level 3
|
Verifications
|
EN50155/EN50121-3-2/EN50121-4; EN45545-1, EN 45545-2 Fire & Smoke verification
|
Stability Testing
|
EN61373 (Shock and Vibration)
|
MTBF
|
495,969 hrs (standards: IEC 62380)
|
Warranty
|
5 years
|
Bypass**
|
Up to two pairs bypass module on 10GT ports to pass to next switch in case of power failure and CPU hang
|
Software Specifications
Management
|
SNMP v1 v2c, v3/ Web/Telnet/CLI
|
SNMP MIB
|
RFC 1213 MIBII RFC 1158 MIB RFC 1157 SNMP MIB RFC 1493 Bridge MIB* RFC 1573 IF MIB RFC 2674 Q-Bridge MIB* RFC 2819 RMON MIB Private MIB
|
ITU G.8032
|
Support ITU G.8032 for Ring protection in less than 20ms for self-heal recovery (single ring enhanced mode) Support basic single ring & enhanced ring Enhanced G.8032 ring configuration with ease Cover multicast & data packets protection
|
PoE Management (PoE model)
|
PoE Detection to check if PD hangs then restart the PD
|
Per Port PoE Status
|
On/ Off, voltage, current, watts, temperature
|
User friendly UI
|
- Auto topology drawing
- Topology demo
- Complete CLI for professional setting
|
Port Trunk with LACP
|
LACP Port Trunk: 8 Trunk groups
|
LLDP
|
Supports LLDP to allow switch to advise its identification and capability on the LAN
|
CDP
|
Cisco Discovery Protocol for topology mapping
|
Enhanced Environmental Monitoring
|
System status for actual input voltage, current, total power load and ambient temperature to be shown in GUI and sent alerting if any abnormal status
|
VLAN
|
Port Based VLAN IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096) GVRP, QinQ, QoS Protocol based VLAN IPv4 Subnet based VLAN
|
Spanning Tree
|
Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 8 MSTI
|
Quality of Service
|
The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP
|
Class of Service
|
Support IEEE802.1p class of service, per port provides 8 priority queues
|
Remote Admin
|
Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder
|
Login Security
|
Supports IEEE802.1X Authentication/RADIUS
|
Port Mirror
|
Support 3 mirroring types: “RX, TX and Both packet”
|
Network Security
|
Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder. 802.1X access control for port based and MAC based authentication/static MAC-Port binding Ingress ACL L2/L3 SSL/SSH v2 for Management HTTPS for secure access to the web interface TACACS+ for Authentication
|
IGMP
|
Support IGMP snooping v1, v2, v3; Supports IGMP static route; 1024 multicast groups; IGMP router port; IGMP query; GMRP
|
MLD Snooping
|
Support IPv6 Multicast stream
|
Static multicast forwarding
|
Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
|
Bandwidth Control
|
Support ingress packet filter and egress* packet limit. The egress* rate control supports all of packet type. Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet. The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress* packet limit.
|
Flow Control
|
Supports Flow Control for Full-duplex and Back Pressure for Half-duplex
|
System Log
|
Supports System log record and remote system log server
|
Protection
|
- Miss-wiring avoidance
- Node failure protection
- Loop protection
|
SNMP Trap
|
Up to 5 trap stations; trap types including:
- Device cold start
- Authorization failure
- Port link up/link down
- DI/DO open/close
- Typology change (ITU ring)
- Power failure
- Environmental abnormal
|
PXE
|
PXE to verify switch firmware with the latest or certain version
|
DHCP
|
Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Snooping, DHCP Option 66; basic IPv6 DHCP server
|
Mac based DHCP Server
|
Assign IP address by Mac in DHCP network
|
DNS
|
Provide DNS client feature and can set Primary and Secondary DNS server
|
NTP/SNTP
|
Supports NTP/SNTP to synchronize system clock in Internet
|
Firmware Update
|
Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade; USB firmware update
|
Configuration import and export
|
Supports editable configuration file for system quick installation; Support factory reset ping to restore all settings back to factory default
|
Enhanced Storm Control
|
prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces
|
ECN
|
Complies with IEC 61375-3-4 (ECN) standard. The support of Ethernet Consist Network allows interconnection between end devices located in single consist of train and interoperability with IEC61375-2-5 (TBN).
|
Optional L3Lite/L3/ETBN
|
Lantech OS4 series are optional upgradable to L3 Lite/ L3 or ETBN communication protocols for future expansion. The optional L3Lite includes editable routing table, VRRP, Router-on-a-stick, Inter- VLAN routing. Optional ETBN complies with IEC61375-2-5 ETBN for Train Backbone Network. Detail SPEC upon request.
|
Diagnostic
|
Support Ping, ARP table and DDM information
|
Dual Image Firmware
|
Support dual image firmware function
|