OVERVIEW
Lantech I(P)GS-6488XSFP is a high performance L2+ (All Gigabit) Ethernet switch with 8 10/100/1000T + 8 100M/1G SFP + 4 1G/2.5G/10G SFP+ auto-sensing cage w/8 PoE 802.3af/at ports which provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring. It also supports enhanced mode with easy configuration, comprehensive QoS, advanced security including INGRESS ACL L2/L3, TACACS+, SSH v2/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ which are important features required in large network. The Cisco Discovery Protocol (CDP) and LLDP are supported for Ciscoworks to detect the switch info and show on L2 map topology.
PoE at/af up to 8 10/100TX Ports with detection and scheduling
Lantech IPGS-6488XSFP supports advanced PoE management including PoE detection and scheduling. PoE detection can detect if the connected PD is hanged then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Each PoE port can be enabled/disabled, get the voltage, current, Watt, and temperature info displayed on WebUI.
Miss-wiring avoidance, Loop protection, Node failure protection
The I(P)GS-6488XSFP also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech I(P)GS-6488XSFP is able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
Support PXE to verify switch firmware with the latest or certain version
The switch can check its firmware version during booting time via PXE protocol. If switch finds any newer version, it will upload automatically.
DHCP option 82 & Port based, Mac based DHCP, Option66, DHCP Snooping, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Snooping is supported. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Basic IPv6 DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes I(P)GS-6488XSFP much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech I(P)GS-6488XSFP features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers enhanced ring and basic ring by easy setup than others. It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI. MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
QinQ, QoS and GVRP supported
It supports the QinQ, QoS, GVRP for large VLAN segmentation.
IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD Snooping and static multicast forwarding binding by ports for video surveillance application.
Enhanced Storm Control
Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces and the detection is more precise and reaction is more efficient.
Optional L3Lite/L3 to be upgradable
Lantech OS3 is optional upgradable to L3 Lite for future expansion. The optional L3Lite includes editable routing table, VRRP, Router-on-a-stick, Inter- VLAN routing.
Editable configuration file; USB port for upload/download configuration
The configuration file of Lantech I(P)GS-6488XSFP can be exported and edited with word processor for the other switches configuration with ease. The built-in watchdog design can automatically reboot the switch when CPU is found dead.
The USB port can upload/download the configuration from/to USB dongle.
2DI/2DO for relay contact and event alerting by email** & traps
In case of event, the I(P)GS-6488XSFP is able to send an email** to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Enhanced Environmental monitoring for Ethernet switch inside information
The enhanced environmental monitoring can detect switch overall temperature, actual input voltage and current. It also can send the SNMP traps and email** when abnormal.
Dual power 24V or 48V input; High PoE budget
The Lantech IPGS-6488XSFP is designed with dual power supply at 24VDC (24V model) and can provide 80W (12V input) or 120W (24V input) PoE budget. The 48V model can support dual power 44VDC~56VDC input and can have 240W PoE budget.
24V/HV input voltage selection: At dual 24VDC (24V model) or single 90~305VAC/120~430VDC (HV model)
The IGS-6488XSFP is able to work at dual 24VDC (24V model). Or with single high power supply at 90~305VAC / 120~430VDC (HV model).
Industrial hardened design with high EFT and ESD protection
Lantech I(P)GS-6488XSFP features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. Featured with relay contact alarm function, the I(P)GS-6488XSFP is able to connect with alarm system in case of power failure or port disconnection. The I(P)GS-6488XSFP also provides ±2000V EFT and ±4000 VDC (Contact) / ±8000 VDC (Air) Ethernet ESD protection, which can reduce unstable situation caused by power line and Ethernet.
It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory applications. The -E model can be used in extreme environments with an operating temperature range of -40°C to 75°C.
SPECIFICATIONS
Hardware Specifications
Standards
|
IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-TX IEEE802.3ab 1000Base-T IEEE802.3an 10Gbase-T IEEE802.3ae 10G Fiber IEEE802.3x Flow Control and Back Pressure IEEE802.3ad Port trunk with LACP IEEE802.1d Spanning Tree IEEE802.1w Rapid Spanning Tree IEEE802.1s Multiple Spanning Tree IEEE802.3ad Link Aggregation Control Protocol (LACP) IEEE802.1AB Link Layer Discovery Protocol (LLDP) IEEE802.1X User Authentication (Radius) IEEE802.1p Class of Service IEEE802.1Q VLAN Tag IEEE802.3at/af Power over Ethernet
|
Switch Architecture
|
Back-plane (Switching Fabric): 112Gbps
|
Mac Address
|
16K MAC address table
|
Jumbo frame
|
10KB
|
Connectors
|
10/100/1000T: 8 x ports RJ-45 with Auto MDI/MDI-X function Mini-GBIC: 8x 100M/1G SFP + 4 x 1G/2.5G/10G SFP+ auto-sensing cage with DDMI RS-232 connector: RJ-45 type USB x 1 Power & Relay connector: 1 x 6-pole terminal block DIDO : 1 x 6-pole terminal block
|
Network Cable
|
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E/ 6 cable EIA/TIA-568 100-ohm (100m) 100Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable; EIA/TIA-568 100-ohm (100m) 1000Base-T: 4-pair UTP/STP Cat5E/6 cable; 10GBaseT:4-pair STP Cat6/6A/7 cable
|
Optical Cable
|
1Gbps: Multi mode: 0 to 550 m, 850 nm (50/125 μm); 0 to 2 km, 1310 nm (50/125 μm) Single mode: 0 to 10 km/ 30 km/ 40 km, 1310 nm (9/125 μm); 0 to 50 km/ 60 km/ 80km/ 120 km, 1550 nm (9/125 μm) 2.5Gbps Multi mode: 0 to 300 m, 850 nm (50/125 μm); Single mode: 0 to 2 km/ 15 km/ 40 km, 1310 nm (9/125 μm); 0 to 40 km/ 80 km/ 100km, 1550 nm (9/125 μm) WDM 1Gbps: Single mode: 0 to 10 km/ 20 km/ 40 km/ 60 km, 1310 nm (9/125 μm); 0 to 80 km, 1490 nm (9/125 μm); 0 to 10 km/ 20 km/ 40 km/ 60 km/ 80 km, 1550 nm (9/125 μm) WDM 2.5Gbps Single mode: 0 to 5 km/ 20 km/ 40 km/ 60 km, 1310 /1550nm (9/125 μm); 0 to 80 km, 1490/1550 nm (9/125 μm) 10Gbps Multi mode: 0 to 300 m, 850 nm (OM3 50/125 μm); Single mode: 0 to 10 km/ 20 km, 1310 nm (9/125 μm); 0 to 40 km/ 80km/ 100 km, 1550 nm (9/125 μm) WDM 10Gbps Single mode: 0 to 10 km/ 20 km/ 40 km/ 60 km, 1270/1330 nm (9/125 μm); 0 to 80km, 1490/1550 nm (9/125 μm)
|
LED
|
Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red); RM(Green) Ethernet port: Link/Activity (Green), Speed (Green); PoE: Link/Act (Green, PoE model); Mini-GBIC: Link/Activity (Green)
|
DI/DO
|
2 Digital Input (DI) : Level 0: -30~2V / Level 1: 10~30V Max. input current:8mA 2 Digital Output(DO): Open collector to 40 VDC, 200mA
|
Operating Humidity
|
5% ~ 95% (Non-condensing)
|
Operating Temperature
|
-20°C~60°C / -4°F~140°F (Standard model) -40°C~75°C / -40°F~167°F(-E model)
|
Storage Temperature
|
-40°C~85°C / -40°F~185°F
|
Power Supply
|
IPGS-6488XSFP Dual DC input, 12V~57V; Dual DC input 16V~60V when using 10G copper (24V model) Dual 44~56VDC (48V model)
IGS-6488XSFP Dual DC input, 12V~60V; Dual DC input 16V~60V when using 10G copper (24V model) Single HV input, 90~305VAC/120~430VDC (HV model)
|
PoE Budget (PoE model)
|
24V model: 24V: 120W / 12V: 80W 48V model: 240W
|
PoE pin assignment (PoE model)
|
RJ-45 port # 1~#8 support IEEE 802.3at/af End-point, Alternative A mode. Positive (VCC+): RJ-45 pin 1,2. Negative (VCC-): RJ-45 pin 3,6.
|
Power Consumption
|
29W without PoE load
|
Case Dimension
|
Metal case. IP-30, IPGS-6488XSFP 95.84 (W) x 135 (D) x 152 (H) mm IGS-6488XSFP 74 (W) x 135 (D) x 152 (H) mm (24V model) 74 (W) x 165 (D) x 152 (H) mm (HV model)
|
Weight
|
900 g
|
Installation
|
DIN Rail and Wall Mount** Design
|
EMI & EMS
|
FCC Class A, CE EN55032 Class A, CE EN55024, CE EN61000-4-2, CE EN61000-4-3, CE EN61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE EN61000-4-8, CE EN61000-6-2, CE EN61000-6-4
|
Stability Testing
|
IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock), IEC60068-2-6 (Vibration)
|
MTBF
|
591,245 (Hrs) (standards: IEC 62380)
|
Warranty
|
5 years
|
Software Specifications
Management
|
SNMP v1 v2c, v3/ Web/Telnet/CLI
|
SNMP MIB
|
RFC 1213 MIBII RFC 1158 MIB RFC 1157 SNMP MIB RFC 1493 Bridge MIB* RFC 1573 IF MIB RFC 2674 Q-Bridge MIB* RFC 2819 RMON MIB Private MIB
|
PoE Management
|
PoE Detection to check if PD hangs then restart the PD PoE scheduling
|
Per Port PoE Status
|
On/ Off, voltage, current, watts, temperature
|
ITU G.8032
|
Support ITU G.8032 for Ring protection in less than 20ms for self-heal recovery (single ring enhanced mode) Support basic single ring & enhanced ring Enhanced G.8032 ring configuration with ease Cover multicast & data packets protection
|
PoE Management
|
PoE Detection to check if PD is hang up then restart the PD PoE Scheduling
|
Per Port PoE Status
|
On/ Off, voltage, current, watts, temperature
|
User friendly UI
|
- Auto topology drawing
- Topology demo
- Complete CLI for professional setting
|
Port Trunk with LACP
|
LACP Port Trunk: 10 Trunk groups
|
LLDP
|
Supports LLDP to allow switch to advise its identification and capability on the LAN
|
CDP
|
Cisco Discovery Protocol for topology mapping
|
Enhanced Environmental Monitoring
|
System status for actual input voltage, current, total power load and ambient temperature to be shown in GUI and sent alerting if any abnormal status
|
VLAN
|
Port Based VLAN IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096) GVRP, QinQ, QoS, Protocol based VLAN; IPv4 Subnet based VLAN
|
Spanning Tree
|
Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree 8 MSTI
|
Quality of Service
|
The quality of service determined by IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP
|
Class of Service
|
Support IEEE802.1p class of service, per port provides 8 priority queues
|
Remote Admin
|
Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder
|
Login Security
|
Supports IEEE802.1X Authentication/RADIUS
|
Port Mirror
|
Support 3 mirroring types: “RX, TX and Both packet”
|
Network Security
|
Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder. 802.1X access control for port based and MAC based authentication/static MAC-Port binding INGRESS ACL L2/L3 SSL/ SSH v2 for Management HTTPS for secure access to the web interface TACACS+ for Authentication
|
MLD Snooping
|
Support IPv6 Multicast stream
|
IGMP
|
Support IGMP snooping v1,v2,v3; 256 multicast groups; IGMP router port ; IGMP query; GMRP
|
Static multicast forwarding
|
Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
|
Bandwidth Control
|
Support ingress packet filter and egress* packet limit. The egress* rate control supports all of packet type. Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet. The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress* packet limit.
|
Flow Control
|
Supports Flow Control for Full-duplex and Back Pressure for Half-duplex
|
System Log
|
Supports System log record and remote system log server
|
SMTP
|
Supports SMTP Server and 8 e-mail accounts for receiving event alert
|
Relay Alarm
|
Provides one relay output for port breakdown, power fail and alarm. Alarm Relay current carry ability: 1A @ DC24V
|
Protection
|
- Miss-wiring avoidance
- Node failure protection
- Loop protection
|
SNMP Trap
|
Up to 5 trap stations; trap types including:
- Device cold start
- Authorization failure
- Port link up/link down
- DI/DO open/close
- Typology change(ITU ring)
- Power failure
- Environmental abnormal
|
PXE
|
PXE to verify switch firmware with the latest or certain version
|
DHCP
|
Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based DHCP; DHCP Snooping; DHCP Option 66; basic IPv6 DHCP server
|
Mac based DHCP Server
|
Assign IP address by Mac that can include dumb switch in DHCP network
|
DNS
|
Provide DNS client feature and can set Primary and Secondary DNS server
|
SNTP
|
Supports SNTP to synchronize system clock in Internet
|
Firmware Update
|
Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade
|
Enhanced Storm Control
|
prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces
|
Optional L3Lite/L3*
|
Lantech OS3 is optional upgradable to L3 Lite/L3* for future expansion. The optional L3Lite includes editable routing table, VRRP, Router-on-a-stick, Inter- VLAN routing.
|
Configuration upload and download
|
Supports text configuration file for system quick installation; Support factory reset button to restore all settings back to factory default; USB for auto restore/backup configuration file
|
Diagnostic
|
Support Ping, ARP table and DDM information
|
Dual Image Firmware
|
Support dual image firmware function
|