10 10/100/1000T + 2 Dual Speed SFP w/ 8 10/100/1000T PoE af/at L2+ Industrial Managed Switch w/ Enhanced G.8032 Ring, PTP & Built-in MMS Server for Data Modeling

Model: IPGS-5408DFT-PT

10 10/100/1000T + 2 Dual Speed SFP w/ 8 10/100/1000T PoE af/at L2+ Industrial Managed Switch w/ Enhanced G.8032 Ring, PTP & Built-in MMS Server for Data Modeling

  • Compliant with IEC61850-3* & IEEE1613*
 

10 10/100/1000T + 2 Dual Speed SFP w/ 8 10/100/1000T PoE af/at L2+ Industrial Managed Switch w/ Enhanced G.8032 Ring, PTP & Built-in MMS Server for Data Modeling

    • Compliant with IEC61850-3* & IEEE1613*
    • Support IEEE802.3at/af up to 30W per port
    • PoE management incl. Detection and Scheduling
    • Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 8/16* MSTI /RSTP
    • Supports PTP IEEE1588 v2 two-step on GTX&GFX ports
    • Built-in MMS server based on IEC61850-90-4 switch data modeling for power SCADA; Unique IEC packet counter for Goose message
    • Miss-wiring avoidance & Repowered auto ring restore (node failure protection)
    • User friendly UI, including auto topology drawing and DDM threshold with dB values***; Complete CLI
    • Support LACP link aggregation, IGMP v3/router port, DHCP server & DHCP Option82 for Port/VLAN based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3, IPv6, SMS
    • Environmental monitoring to display inside switch temperature, voltage, current & send alerting when abnormal
    • HV or DC input voltage model selection



OVERVIEW

Lantech IPGS-5408DFT-PT is a IEC61850-3 compliant high performance L2+ (Gigabit uplink) switch with 10 10/100/1000T + 2 100M/1000M Dual Speed SFP which provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms including auto mode, enhanced mode & multiple VLAN mode* for easy configuration, comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ* (double tag VLAN) which are important features required in train and large network. It also supports Cisco Discovery Protocol (CDP) and LLDP for Ciscoworks to detect the switch info and show on L2 map topology.

Support IEC61850-90-4 switch data modeling with built-in MMS server
Lantech IPGS-5408DFT-PT embeds a MMS server based on IEC61850-90-4 switch data modeling for power SCADA that allow power SCADA to control and monitor the switch without additional NMS.

2-Step PTP on all GigaT&FX ports
Lantech IPGS-5408DFT-PT features hardware-based PTP IEEE1588 v2 two-step function which can allow all Gigabit ports to synchronize the network with precise accuracy.

Miss-wiring avoidance & Loop protection
The IPGS-5408DFT-PT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPGS-5408DFT-PT is able to alert with the LED indicator and send out an email, traps or a SMS text. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.

FEATURES

  • 10 10/100/1000T + 2 100M 1000M Dual Speed SFP w/8 PoE 802.3af/at Injectors (Total 12 Ports Switch)
  • Embedded 8 PoE Injectors IEEE802.3af/at function to feed power up to 30W for active mode operation.
  • Max. PoE budget: 120W
  • Compliant with IEC61850-3 & IEEE 1613
  • IEEE 1588 PTP v2 two-step at 12 Giga ports
  • Support IEC 61850 over MMS (TCP/IP Ethernet)
    • Provide .cid file type
    • Solicited data access through Manufacturing Message Specification (MMS) Read and Write requests
    • Unsolicited data through MMS Information Reports
  • Back-plane (Switching Fabric): 24Gbps
  • 16K MAC address table
  • DDM to support SFP diagnostic function***
    • Automatically convert the raw data into dB values for TX power/RX power, making it easier to measure the fiber distance
  • 10KB Jumbo frame supported on all ports
  • User friendly UI, auto topology drawing, topology demo, complete CLI for professional setting
  • Enhanced G.8032 Ring protection in 20ms < 256 switches
    • Support various ring/chain topologies, including multi-ring & multi-VLAN ring*
    • Enhanced G.8032 ring configuration with ease
    • Auto ring configuration(auto mode) for single ring
    • Ring covers multicast on different ports
  • Built-in RTC (Real Time Clock) to keep track of time
  • Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
  • IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy
  • 4K 802.1Q VLAN, Port based VLAN, GVRP*, QinQ*
  • Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console/ LantechTM InstaConfig**/ LantechTM InstaView**
  • DHCP server / client / DHCP Option 82 relay / DHCP Option 82 server;  Port/VLAN based DHCP distribution; DHCP Option 66
  • Mac based DHCP server to assign IP address that includes dumb switches in DHCP network
  • Bandwidth Control
    • Ingress packet filter and egress rate limit
    • Broadcast/multicast packet filter control
  • Relay alarm output system events
  • Miss-wiring avoidance
    • LED indicator
    • Email, traps, or SMS notification
  • Repowered auto ring restore
    • Ensure the switches in a ring to survive after power breakout is back
    • The status can be shown in NMS when each switch is back
  • TFTP/HTTP firmware upgrade; LantechTM InstaConfig** for multiple upgrade
  • System Event Log, SMTP Email alert, SMS mobile (text) and SNMP Trap for alarm support; 32 RMON counters
  • Security
    • SSL/SSH/INGRESS/EGRESS ACL L2/L3
    • Port Security: MAC address entrIES/Filter/MAC-Port binding
    • IP Security: IP address security management to prevent unauthorized intruder.
    • Login Security: IEEE802.1X/RADIUS
    • HTTPS for secure access to the web interface
  • Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
  • Multicast static route for non- IGMP camera to prevent flooding; IGMP router port to assign query in ring and for reversed multicast video flow
  • IGMPv1,v2,v3 with Query mode for multimedia; GMRP*
  • Factory reset button to restore setting to factory default
  • Watchdog design to auto reboot switch CPU is found dead
  • Environmental monitoring for system input voltage, current, ambient temperature
  • Dual DC input from 45V~57VDC
  • Provides EFT protection ±4K VDC for power line
  • Supports ±8K contact/ 15K air Ethernet ESD protection
  • Supports DIDO (Digital Input/Digital Output)
  • IP30 metal housing with DIN rail and Wall-mount** design

SPECIFICATIONS

Hardware Specifications

Standards

IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX
IEEE802.3ab 1000Base-T Ethernet
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE802.3ad Link Aggregation Control Protocol (LACP)
IEEE802.1AB Link Layer Discovery Protocol (LLDP)
IEEE802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE802.3at/af Power over Ethernet

Switch Architecture

Back-plane (Switching Fabric): 24Gbps

Transfer Rate

14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet / Gigabit Fiber port

CPU

Marvell 800Mhz

RAM

256M Byte

Flash

128M Byte

Mac Address

16K MAC address table

Jumbo frame

10KB on all ports

Connectors

10/100/1000T: 10 x ports RJ-45 with Auto MDI/MDI-X function
Mini-GBIC: 2 x 100/1000 SFP socket with DDM
RS-232 connector: RJ-45 type
Power & Relay connector: 1 x 6-pole terminal block
DIDO : 1 x 6-pole terminal block

Network Cable

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)

Optical Cable

1.25Gbps:
Multi mode: 0 to 550 m, 850 nm (50/125 μm); 0 to 2 km, 1310 nm (50/125 μm)
Single mode: 0 to 10 km/ 30 km/ 40 km, 1310 nm (9/125 μm); 0 to 50 km/ 60 km/ 80km/ 120 km, 1550 nm (9/125 μm)
125Mbps:
Multi mode: 0 to 2 km/ 5 km, 1310 nm (62.5/125 μm)
Single mode: 0 to 30 km, 1310 nm (62.5/125 μm)
WDM 1.25Gbps:
Single mode: 0 to 10 km/ 20 km/ 40 km/ 60 km, 1310 nm (9/125 μm); 0 to 80 km, 1490 nm (9/125 μm); 0 to 10 km/ 20 km/ 40 km/ 60 km/ 80 km, 1550 nm (9/125 μm)
WDM 125Mbps:
Single mode: 0 to 20 km/ 40 km/ 60 km/ 80 km, 1310 nm (9/125 μm); 0 to 20 km/ 40 km/ 60 km/ 80 km, 1550 nm (9/125 μm)

Protocol

CSMA/CD

LED

Per unit: Power 1 (Green), Power 2 (Green), FAULT (Red)
Ethernet port: Link/Activity (Green), Speed (Green); Mini-GBIC: Link/Activity (Green)
R.M. indicator (Green)
PoE : Active (Green)

DI/DO

2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
2 Digital Output(DO): Open collector to 40 VDC, 200mA

Operating Humidity

5% ~ 95% (Non-condensing)

Operating Temperature

-20°C~60°C / -4°F~140°F (Standard model)
-40°C~75°C / -40°F~167°F(-E model)

Storage Temperature

-40°C~85°C / -40°F~185°F

Power Supply

Dual isolated power input (45~57VDC)

PoE Budget

Max. 120W
(54V input is recommended for PTZ or heater applications)

PoE pin assignment

RJ-45 port # 1~ # 8 support IEEE 802.3at/af End-point. Per port provides up to 30W
Positive (VCC+): RJ-45 pin 1,2.
Negative (VCC-): RJ-45 pin 3,6.

Power Consumption

10W

Case Dimension

Metal case. IP-30,
Standard model: 74 (W) x 135 (D) x 152 (H) mm
-E model: 96 (W) x 135 (D) x 152 (H) mm

Weight

900 g

Installation

DIN Rail and Wall Mount** Design

EMI & EMS

FCC Class A,
CE EN55032 Class A, CE EN55024, CE EN61000-4-2, CE EN61000-4-3, CE EN61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE N61000-4-8
EN50121-4

Stability Testing

IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock), IEC60068-2-64 (Vibration)

Compliance Report

IEC61850-3, IEEE1613

MTBF

289,712 hrs

Warranty

5 years

Software Specifications

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1215 Traps MIB*,
RFC 1213 MIBII
RFC 1158 MIBII
RFC 1157 SNMP MIB*,
RFC 1493 Bridge MIB*,
RFC 1573 IF MIB
RFC 2674 VLAN MIB, 
Partial RFC 1757 RMON,
RFC 2674 Q-Bridge MIB*; Bridge MIB*,
LLDP MIB*
RSTP MIB*
Private MIB

MMS for data modeling

IEC 61850 over MMS (TCP/IP Ethernet)
Provide .cid file type
Solicited data access through MMS read and write requests
Unsolicited data access through MMS information reports

ITU G.8032

Support ITU G.8032 for Ring protection in less than 20ms for self-heal recovery (incl. multicast packets)
Support various ring/chain topology IES
Includes multi-ring & multi-VLAN ring*
Enhanced G.8032 ring configuration with ease
Ring covers multicast on different ports

PTP v2

Support hardware-based IEEE1588 PTPv2, End to End (2-step) and Peer to Peer (2-step) modes in Transparent Clock, with 12 Giga ports

User friendly UI

  1. Auto topology drawing
  2. Topology demo
  3. Auto configuration for G.8032(auto mode) for single ring
  4. DDM threshold with dB values***
  5. Complete CLI for professional setting

Port Trunk with LACP

LACP Port Trunk: 8 Trunk groups/Maximum 8 trunk members

LLDP

Supports LLDP to allow switch to advise its identification and capability on the LAN

CDP

Cisco Discovery Protocol for topology mapping

VLAN

Port Based VLAN
IEEE 802.1Q Tag VLAN / VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096.)
GVRP*, QinQ*, QOS QinQ*

IPv6/4

Present

Spanning Tree

Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree

Quality of Service

The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP

Class of Service

Support IEEE802.1p class of service, per port provides 8 priority queues

QoS by VLAN

Tagged QoS by VLAN for all devices in the network

IP Security

Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.

Login Security

Supports IEEE802.1X Authentication/RADIUS

Port Mirror

Support 3 mirroring types: “RX, TX and Both packet”

Network Security

Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.
802.1X access control for port based and MAC based authentication/MAC-Port binding
Ingress/Egress INGRESS/EGRESS ACL L2/L3 L2/L3
SSL/ SSH for Management
HTTPS for secure access to the web interface
TACACS+* for Authentication

IGMP

Support IGMP snooping v1,v2,v3; Supports IGMP static route; 1024 multicast groups; IGMP router port ; IGMP query; GMRP*, QinQ*, QOS QinQ*

Static MAC-Port Bridge

Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application

Bandwidth Control

Support ingress packet filter and egress packet limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet.
The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet limit.

RTC

Built-in Real Time Clock to keep track of time always

Flow Control

Supports Flow Control for Full-duplex and Back Pressure for Half-duplex

System Log

Supports System log record and remote system log server

SMTP/Text SMS

Supports SMTP Server and 8 e-mail accounts for receiving event alert; can send SMS text alert via mobile

Relay Alarm

Provides one relay output for port breakdown, power fail and alarm.
Alarm Relay current carry ability: 1A @ DC24V

Protection

  1. Miss-wiring avoidance
  2. Repowered auto ring restore
  3. Loop protection

SNMP Trap

Up to 10 trap stations; trap types including:

  1. Device cold start
  2. Authorization failure
  3. Port link up/link down
  4. DI/DO open/close
  5. Typology change(ITU ring)
  6. Power failure
  7. Environmental abnormal**

DHCP

Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based/VLAN based DHCP distribution (DHCP relay agent); DHCP Option 66

Mac based DHCP Server

Assign IP address by Mac that can include dumb switch in DHCP network

DNS

Provide DNS client feature and support Primary and Secondary DNS server.

SNTP

Supports SNTP to synchronize system clock in Internet

Environmental Monitoring

Internal sensor to detect temperature, voltage and current and send SNMP traps, SMS and emails if any abnormal events

Firmware Update

Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade; LantechTM InstaConfig** for multiple upgrade

Configuration
upload and download

Supports text configuration file for system quick installation; Support factory reset button to restore all settings back to factory default

IfAlias

Each port allows an alphabetic string of 128-byte assigned as its own unique name via the SNMP or CLI interface

Sản phẩm khác